Useful information for concrete plant design and maintenance

Scale-Tron manufactures High Pressure Washout system for Concrete Mixers, Temperature Sensors for use in concrete production and also Bagged Fiber Dispensers.  The company also imports Concrete Mixers and Bulk Fiber Dispensers from Italy.
The mixer washout system that really does a job – any mixer, any plant.
TempTron 2610 is a temperature sensor that stands up to the abrasive wear in aggregate bins and mixers.
Eliminate the cost of throwing bags of fiber into your mixer or trucks with a dispenser that really does a job.
Dispenser for bags of fiber.  Load it and forget it. Bags are dispensed into the concrete mixer or truck, one per yard of concrete or whatever you choose, from the formula, exactly like admixtures.
Great technical tips for all concrete plants.

Getting proper information from water and admix meters

Does the batching computer for your concrete plant always give exactly the right amount of admix and water? It probably doesn't, but you'll never know it. The big admix companies use a practice that makes their equipment look better than it really is; as a result, you could be using (and paying for) more admix than you think . . . Read more

Admixture companies usually pre-wire their ontrols so that the power for the meter comes from the filling valve solenoid output on the computer.  As a result, at completion of the filling , when the valve turns off, the meter stops counting. This does not necessarily stop the flow of admix, however.  If the flow was fast, it probably continues for a fraction of a second before the valve closes.

This can translate into a few ounces or many milliliters in every batch. Even worse, consider the valve that sticks in the OPEN condition.  Admix will continue filling, possibly at a much reduced rate, during bottle discharge and all the time up to the start of the next batch. The control system will not record it and only a very alert operator will spot it.

The solution is to re-wire the admix controller, which we do on almost every installation.  Power the meter from a solid power source (see diagram). As long as the batching computer monitors the meter after shutting off the valve, it will catch the errors above.

Wire water valves and meters in the same manner.

P.S. – Master Builders assures us that they wire their admix systems;  the above change is not necessary!  Thanks for the feedback.

Improve jogging performance with flow control valves

Big feed gates with large operating cylinders can open very quickly. When jogging at the end of the feed period, the objective is to release small bursts of material with each jog . . . Read more

Concrete plant batching controllers usually control the “open time” of the gate in steps of 1/10 to 1/100 second.  Since it takes 1/10 to 2/10 second to start the gate moving, and it can be full open in 3/10 second, a setting of 2/10 may drop no material while a setting of 3/10 can drop 50lb/20kg.  This is too much for accurate batching. The computer’s automatic tuning can try to adjust the jog time but it could jump from 2/10 to 3/10 second and back again in successive batches. This is futile and will result in lost time and tolerance errors.

The solution is to add a flow control valve in the opening direction only. When adjusted to a speed of 1 second (approximately) from closed to full open, the open time plus the size of the opening can be adjusted in small steps. Since the volume of material dropped in each jog is roughly proportional to the area under the curve (see diagram), you can control the amount of each drop by the same 1/10 second steps. This allows the automatic tuning (assuming that your system has it) to easily adjust to the best setting.  Update, 2016:  Most PLCs now have timers with 1/100 second increments, so a faster closing rate is possible – but the principle still applies!

Checking your scale calibration

We had a situation several years ago where a concrete plant had been making sub-standard product. We found that the cement scale read 20% too high and it weighed out too little cement on each batch . . . Read more

Understandably, our customer was very upset. The fact is, however, that the customer is responsible for checking his equipment, and that includes scales. This was an extreme case, but it shows very clearly what can happen when we blindly believe our instruments. Even if the customer checks the scales every 6 months, things like this can happen.

We recommend that the customer checks his batching scales every week by having someone apply his body weight to each scale, while someone else reads the display. This is rough and ready, but will find gross errors quickly before much damage is done. A better way is to use our SHUNT CALIBRATOR unit, which connects to each scale in turn. It simulates a known weight, checking the complete load cell circuit as well as the indicator. This avoids the need for test weights during weekly tests, but you should do a six monthly calibration test to meet quality plan requirements.

Improve concrete plant performance

Does the shock of aggregate hitting the bottom of the weigh hopper cause your scale reading to bounce? Do you get out of tolerance weights as a result? Many systems exhibit this type of performance but it is easy to correct . . . Read more

A piece of 6″ angle, welded across the hopper directly under each gate, will reduce the momentum of the falling material and spread the pile of aggregate, allowing a little more to be batched into the hopper before it touches the gate. More important, however, it allows the scale to react instantly to the falling material. This removes the bounce effect while shortening the response time of the scale.

This is also very effective when batching small quantities of material. Without the angle, it has to fall to the bottom of the hopper before the scale can react.  In consequence it increases the possibility for overshoot before the gate can close. The angle allows the system to react properly regardless of the transit distance.  The gate closes normally and you can jog it to obtain greater accuracy.  Size of the angle is not critical, but it should intercept at least 50% of the flow to be effective.

Load cell, S-typeChoice of load cells can be crucial

Many concrete plant batching scales today are suspended from tension load cells. Usually 4, but sometimes 3 of the popular S type cells can support a scale hopper or conveyor. Many people installing their own equipment use these cells but do not fully understand their differences . . . Read more

To do a proper job, all load cells on the same scale must have equal sensitivity.  Alternatively, you should equalize them by means of a “summing box”. We call load cells with equal sensitivity (within 1/4% or better) “standardized”.  On a concrete batching scale, there is no need to balance the cells further.  This eliminates the need for a summing box and the consequential lengthy adjustment procedure.

Most models of the “S” cell are are low in cost and hence are not standardized. This makes it imperative to use a summing box and go through the “corner adjustment” procedure with test weights before the scale can be used. Consider this fact carefully before making your choice of load cells.  The corner test might be difficult or impossible to carry out because of lack of room, danger to personnel or insufficient time.

We know which load cell types are standardized and can be used on batching scales of all types.  Contact us for further information.

Can you run out of admix without knowing it?

If your concrete plant uses the popular types of pump and admix meters, the answer is probably YES! Many pumps will happily pump air, and the meter will measure it just as though it was admix. Even if you have sight glasses, it is possible for no-one to notice it . . . Read more

You make batch after batch with no admix.  This can be a disaster. Fortunately, there is an easy fix. You can add a simple proximity detector to the outside of the plastic admix tank.  This allows early warning of low admix level. When connected to BatchTron inputs, alarm messages can be generated.

Even better is to use our SiloWeigh system with liquid tank sensors.  This gives you a display of the amount in each tank and programmable alarms too.

We have installed these sensors in concrete plants. Call us for details.

Cure a common cement scale problem

If you have a cement weigh hopper (or something similar), you might find that its empty reading changes from when the discharge valve is open to when it is closed. This can be severe enough to prevent start of the next batch if the control system checks the empty weight before starting, as it should do . . . Read more

The reason is almost always an air pressure difference between the interior of the hopper and the vessel which it feeds (typically the mixer).  If the plant builder attaches a dust extractor to the mixer, aerates the hopper (to aid in discharge) or merely fills the materials into the mixer, it displaces air and a pressure difference results.

The solution is to add a bypass pipe.  This can be as simple as connecting a length of flexible plastic hose 3″ or 4″ in diameter, to the top of the cement hopper.  The other end connects to the mixer or receiving vessel.  This equalizes the pressure at both sides of the discharge valve as well as the feed point (see diagram).  In turn, it eliminates any vertical force on the load cells or scale.  An important side benefit is that it provides a path for air displaced during both filling and discharge, speeding operation and eliminating another source of weight error during feeding.  Any dust in this displaced air returns to the mixer and the dust collector, if used, evacuates it.

Be careful to use flexible hose (the corrugated type is best).  Secure it to the building structure to prevent it affecting normal weight readings.  Note also that for larger hoppers, and some mixers that can plug up this pipe with cement and water, a filter is preferable.

Butterfly valve saves cement dollars

On an older concrete plant, whether for ready-mix or products, screw feeders are usually used for the cementitious materials. The feed from these feeders is not constant, however, and has a large variation depending on the rotation of the screw flights . . . Read more

Each time the motor stops, the overfeed depends on the screw position and will vary.  Assuming that the batching computer has accurately compensated for the “in-flight” material, the end weight will be over or under the target weight because of this variation.  As a result, it forces the concrete plant operator to add a little extra cement on every batch.  This costs a huge amount over a year’s production.  Alternatively, excessive aeration of the cement silo, needed to improve flow, can cause fluidization of the cement in the screw feeder which then creates an overweight situation.

You can eliminate both these problems by adding a fast acting butterfly valve under the screw feeder exit.  If the exit tube is long, it should be as close to the cement scale as possible to minimize the in-flight amount.  Be sure to fit a very flexible sock between this valve and the scale to minimize the effect on the weight reading.

You should actuate the valve operating cylinder from a solenoid valve and connect it to the motor starter for the screw feeder.  If you are worried about the valve failing to open, mount a limit switch on the valve and use it to close the circuit to the screw feeder motor starter.

The resultant material saving on most feeders averages 1/2 to 1%.  Add this up over a year’s production;  you can probably justify a new BatchTron system with the amount you save!

Protect batching system from power surges

Several end users of our products have had mysterious failures of moisture sensors and load cells. Analysis of the components show that a high voltage has broken down the insulation between the circuit board or sensor and the metal case. This destroys all or part of the electronics as well as the sensor or load cell . . . Read more

This is caused by a high voltage appearing on the outer cabinet of the controller.  The high voltage transfers to everything inside it, eventually finding the shortest path to ground through the offending device.  This occurs when the path from the controller to earth ground is long.

In one case, the phone line into the concrete plant had its lightning arrester ground point connected to the controller cabinet but there was only a thin 16 gauge ground wire from the cabinet to power ground about 50 ft away.  Static discharges (due to nearby electrical storms and induced voltages from power lines) traveled down the phone lines to the cabinet ground.  From there it went to the moisture sensor and load cells and grounded at the plant frame, frying the sensor and load cell in the process.  A European-style power system with power line neutral coming in through overhead cables can be just as bad.

The path for the incoming surge is through the power line, power neutral, telephone line or other overhead wire to the control cabinet.  The analog inputs for the moisture sensors and load cells are grounded to the cabinet.  They conduct this surge to the moisture sensor or load cell, where it jumps the insulation, to ground itself through the concrete plant’s frame.

The solution is simple and effective.  Connect the plant frame to the controller cabinet with a thick (#10 gauge or 5 mm) ground cable as short as possible.  This minimizes the voltage that can appear between the two and reduces the risk of striking through the insulation of the sensor or load cell. We recommend that you do this on all plants, regardless of whether they have had a problem or not.  It’s just good insurance.  If the problem appears to be severe, it also helps to put an isolating transformer (equal voltage input and output) in the power line before the controller (and before the UPS if used, since most UPSs do not provide isolation).

Much as we love the business that lightning, fires and floods bring, we appreciate that it costs your business a lot of money when it happens.  You might also want to consult us on the best grounding methods if you’re not sure.  Most of the time we can do it without a site visit.